J-VALVES · Ball Valve Manufacturer · Wenzhou, China info@j-valves.com +86-13600648865

J-VALVES ball valve news
Home News

Ball Valve News & Technical Insights from J-VALVES

Technical articles, manufacturing updates and project cases from the J-VALVES ball valve factory in Wenzhou, China. Written by our engineering and sales team - covering API 6D, API 607, cryogenic testing, OEM manufacturing and real orders from oil & gas, LNG and water projects worldwide.
Urea Plant Ball Valves: The Wetted Path Survives Only While Oxygen Is Being Fed To It

Urea Plant Ball Valves: The Wetted Path Survives Only While Oxygen Is Being Fed To It

Carbamate at 150 bar and 185 C eats stainless 50 times faster once the passive film starves. The valve cavity is where the oxygen runs out first.
Read More
Stiction: What A Ball Valve Becomes When Nobody Turns It

Stiction: What A Ball Valve Becomes When Nobody Turns It

A valve that stood closed for years has not worn out. The seat has bonded to the ball, and the first stroke is a step, not a ramp. What the trace shows.
Read More
Molten Salt Ball Valves: The Valve Works at 565 C And Dies at 219 C

Molten Salt Ball Valves: The Valve Works at 565 C And Dies at 219 C

Salt freezes at 220 C and decomposes at 565 C. Everything a molten salt ball valve does happens in that 345 kelvin gap, and the gap is not generous.
Read More
Direct Air Capture Ball Valves The Vacuum Side Runs The Seal Backwards, And Three Hundred Thousand Strokes Decide The Design

Direct Air Capture Ball Valves The Vacuum Side Runs The Seal Backwards, And Three Hundred Thousand Strokes Decide The Design

A solid sorbent DAC plant moves 1.3 million cubic metres of air per tonne of CO2, then asks a DN50 ball valve to hold 0.9 bar from the wrong side.
Read More
Your Ball Valve Is Not A Test Blind: What A Hydrotest Does To The Seats

Your Ball Valve Is Not A Test Blind: What A Hydrotest Does To The Seats

A line test puts pressure on the wrong side of the seat logic, above the valve's own seat test, with water that stays in the pocket. What to arrange instead.
Read More
Remanufactured Ball Valves: Five Checks That Decide Whether A Rebuild Deserves A Certificate

Remanufactured Ball Valves: Five Checks That Decide Whether A Rebuild Deserves A Certificate

A rebuild at 45 percent of price with half the life is no saving. Five checks that separate a real remanufacture from a repaint with a certificate.
Read More
The Squeeze Is A Residual: How Tolerance Stack-Up Decides Whether A Ball Valve Seals

The Squeeze Is A Residual: How Tolerance Stack-Up Decides Whether A Ball Valve Seals

No dimension sets the seat squeeze. Five tolerances do, in series. Why identical valves feel different, and why a new ball changes the arithmetic.
Read More
Why A Ball Valve Gets Harder To Turn: Five Causes, And The Test That Tells Them Apart

Why A Ball Valve Gets Harder To Turn: Five Causes, And The Test That Tells Them Apart

A ball valve that stiffens over months points at one of five parts. Measure torque with the line pressurised and again vented, and the split becomes visible.
Read More
The Ball Valve at Four Thousand Bar: Seat Load, Erosion And Fatigue in Waterjet Circuits

The Ball Valve at Four Thousand Bar: Seat Load, Erosion And Fatigue in Waterjet Circuits

At 4,000 bar a 10 mm bore puts 31 kN on the seat and a 0.1 mm leak cuts steel. What a ball valve must survive in a waterjet or intensifier circuit.
Read More
Large Diameter Ball Valves: Four Limits That Change The Design

Large Diameter Ball Valves: Four Limits That Change The Design

Above a certain size a ball valve stops being a scaled one. Ball weight, operator torque, body split and the test bench each set a limit at a different size.
Read More